Corporation (USG) consists of five wholly-owned subsidiaries, United States Gypsum Company, USG Interiors, Canadian Gypsum Company, L&W Supply Corporation, USG Mexico and USG International. Its North American operations encompass 56 manufacturing and warehousing sites operating 34 gypsum board lines, five cement board lines, 20 joint treatment facilities, seven paper mills, nine quarries/mines and 11 ceiling product lines. The corporation employs approximately 1,800 maintenance personnel (mechanical, electrical and process controls) with an annual maintenance budget exceeding $150 million.
Asset care best practices
USG began its implementation of asset care and work management best practices in 2001. The goal of this project, which has come to be known as the Reliability Performance Model and the RPM Initiative, was to develop a world class asset management program utilizing recognized best practices that focused on the areas of equipment reliability and maintenance productivity to improve plant operating efficiencies. The aim was to change the corporation's maintenance departments from being fire fighters and emergency-based into departments that are based on prevention with controls in place to be proactive.
The resulting RPM Initiative is a structured and disciplined approach that focuses on increasing production output through equipment performance and workforce productivity improvements. Today, it continues to strongly influence the way asset care, maintenance and reliability are managed at USG's manufacturing facilities.
The work management portions of the program, work orders, planning, scheduling and shutdown coordination form the foundation of the model, as shown in Fig. 1. These are the core competencies that are the focus of the current training. All manufacturing facilities are employing planners and building central storerooms to support this effort.
USG looked to the RPM Initiative to deliver in several ways, including helping the corporation:
These core competencies support USG's proactive organization, which:
This work will lead to a phase where the organization builds on it successes. By putting this model into place at all USG manufacturing facilities, the company should be able to drive a culture of reliability and continuous improvement.
USG continues to implement the RPM Initiative in phases (approximately 10 facilities each year). The first implementation began with two pilot projects in 2001 - 2002. Based on the success of those pilots, the initiative became a company -wide program. The model was then rolled out to an additional 33 facilities. The plan is to continue the implementation until all 56 manufacturing facilities have been trained and are implementing the model. Three years into the project, sites that had embraced the initiative were reporting:
Teamwork has been a critical component to the success of this initiative. All USG employees understand that the RPM Initiative is a company- and plant-wide program—not just a maintenance or planner program. They also understand that the production departments are integral to the success of this initiative, and their involvement has been another reason for the program's success.
Asset care metrics
Another key to the program's success has been the corporation's ability to measure maintenance performance. Relevant and standardized metrics have been developed to foster continuous improvement by involving employees at every level within the organization.
Key Performance Indicators (KPIs) and expectations were developed at the beginning of the RPM Initiative. They're what are used to drive improvements—and what USG uses to measure its performance.
The KPIs provide information on where the process is working well and where it isn't. This helps the corporation build on its successes and leads it to making process changes where unfavorable trends are developing. Table I highlights the Maintenance Benchmarks USG uses for rating various KPIs, along with the ratings for a typical USG plant.
Plant key performance indicators
During the pilot implementations, USG realized that it needed to measure the program's progress. While the organization was collecting a large amount of information in its computerized maintenance management software (currently DataStream's MP2 Access 2000) via the work order system, it realized that the data was only useful if it could be utilized to support decision making.
With the assistance of PCA, a set of Plant KPIs that focused on measuring the process and its implementation were developed. The following reflects the first 13 of the 26 KPIs currently utilized by USG.
1. Monthly Maintenance Spending (by dollar)
KPI #1 breaks out maintenance spending for labor, materials and contractors during the month.
2. Monthly Maintenance Spending (by %)
KPI #2 provides the same information as KPI #1, but shows the percentage of maintenance spending for labor, materials and contractors during the month.
Benchmark: Maintenance labor and material costs should be balanced operating close to a 50/50 split. Balanced costs indicate cost efficiency. High labor costs may indicate craftspeople are working ineffectually. High materials costs may indicate something is wrong with parts reliability or preventive maintenance.
3. Monthly Work Mix by Priority
KPI # 3 uses work order priority codes to define when a work order should be done relative to others. It calculates the percent of hours worked for the month for each work order priority (shown in Table II: Work Order Priorities), providing a clear picture of what kind of work is being done, e.g. routine, break-in, emergency or down day. Benchmark: Less than 10% of the completed work should be reactive (emergency/urgent/break-in, i.e. priorities 1, 2 and 5.)
4. Monthly Work Mix by Type (hours)
KPI # 4 is the work order type code that indicates the nature of the work performed (e.g. preventive, repair, rebuild, modify, etc.).
Each work order is coded with a work order type (as shown in Table III: Work Order Types). This KPI breaks out the work orders completed during the month by type based on actual hours charged against the work order. As with KPI #3, KPI #4 helps to provide a clear picture of what kind of work is being done.
5. Monthly Work Mix by Type Summary (%)
KPI #5 provides the same information as KPI #4, but summarizes each major work order type as a percentage of hours worked during the month.
Benchmark:40% of all hours worked should be preventive and condition based maintenance (PPM—Preventive and Predictive Maintenance).
A second benchmark measures PPM effectiveness. 15% to 30% of all hours worked should be generated from PPM inspections (FROMPM). You want your PPMs finding defects. If PPMs are not finding defects, then you may be doing the PPM too frequently or ineffectively. If you find too many defects during your PPMs then you may not be doing the PPMs often enough.
By setting these PPM benchmarks, USG is placing a priority on preventive work to drive equipment reliability improvement.
6. Monthly Work Mix by Expense Class
KPI # 6 uses an expense class code on the work order that is used to further define the type of work. It calculates the percentage of hours worked during the month for each expense class (as shown in Table IV: Work Order Classes).
7. Completed Work Orders per Man Day
KPI #7 provides the monthly trend for the past 12 months of the number of work orders completed per craftsperson.
Benchmark: Three work orders per person per day and trending up.
KPI #7 can be negatively impacted at plants where there is a high percentage of project and rebuild work thattends to be single work orders for large time commitments (e.g. 40 hours per week for a single work order).
8. Priority 1 Equipment Closed Emergency Work Orders
KPI # 8 tracks emergency work orders by the priority of the equipment. Equipment Priorities range from 1 (regulatory) to 9 (least critical) and are detailed in Table V: USG Equipment Priority Codes.
KPI #8 provides information on the number of emergency work orders completed on the plant's most critical equipment during the month. This is a "bad actor" report and it is used to help focus or direct where resources should be placed to address problems (e.g. increased inspections, preventive work, predictive work, failure analysis, etc.).
9. Equipment Other than Priority 1 with 4 or More Closed Emergency Work Orders
KPI #9 provides another snapshot of the "bad actors." It identifies equipment other than Priority 1 units with repetitive problems, as indicated by multiple emergency work orders to help identify where additional preventive work is required (e.g. increased inspection frequencies, PPM optimization, failure analysis, etc.).
10. Equipment with Costs Greater than $1000
KPI #10 is similar to the previous two KPIs as it is providing information on equipment that is expensive to maintain, to help identify where to focus efforts (e.g. review PPMs, plan capital replacements, initiate upgrades, etc.).
11. Failure Codes
KPI #11 provides information on the craftsperson's initial assessment of the cause of the failure (refer to Table IV: Failure Codes, for a partial listing of the failure codes available). This information is used to assist with root cause failure analysis, as well as to determine training needs (i.e. alignment is a common failure), PPM requirements (i.e. wear is a problem), lubrication improvements (i.e. lube failures are high), etc.
12. Job Delays
KPI #12 provides reasons for the various job delays for the month. After a work order has been completed, the craftsperson codes the work order with a job delay code. The job delay code explains what, if anything, caused a job to take longer than anticipated (i.e. charged hours are greater than estimated hours). The primary sources of job delays are interruptions (reactive issues) equipment readiness (scheduling issues), job scope changes and tools/material readiness (planning issues) and material problems (storeroom issues).
Benchmark: Zero (0) job delays due to planning, scheduling, and materials management.
13. PPM and SAR Completion Times
KPI #13 provides information on how well USG is managing its preventive maintenance and OSHA-required safety inspections (SAR), and whether the work is being completed when scheduled.
Work orders closed with $0 charged indicate that the PPM or SAR work was not completed, although it was scheduled. Plants should be evaluating why PPMs and SARs are not being completed.
Benchmark: Zero (0) PPM/SAR work orders not completed in the scheduled period. Part II of this article will appear in the next issue of Maintenance Technology. It will cover the final 13 KPIs used by USG and detail the results the corporation has seen since it began utilizing these metrics. MT
Jay Padesky is Technical Manager Manufacturing Reliability and Maintenance for the US Gypsum Co. He is a Registered Professional Engineer (Michigan) and a Certified Maintenance and Reliability Professional (CMRP) with over 25 years of experience in various engineering and management positions. Since 2002, he has headed up USG's RPM Initiative, which is instituting work management, material management and reliability best practices at all 56 USG North American manufacturing locations. Padesky is active in the Society of Maintenance and Reliability Professionals (SMRP), where he is a member of the association's Best Practices Committee. He holds a Bachelor's degree in Chemical Engineering from the University of Michigan.
Dick DeFazio is the president and CEO of Performance Consulting Associates, Inc. (PCA, Inc.), an asset management consulting and engineering firm headquartered in Atlanta, GA, since 1976. He is a Board Certified Management Consultant (CMC) with over 25 years of experience in both the public and private sectors. He and his team help corporations implement Best Practices