Big Money Talks: Calculating True Motor Efficiency

1023livotimugThe Energy Independence Security Act of 2007 (EISA) becomes law December 19, 2010. A portion of EISA covers induction motors from 1-500 hp. It's safe to say most end users will be affected.


What does EISA have to do with calculating true motor efficiency? More than you would think. At some point, you'll need to replace a motor covered by EISA. Replacing it with a duplicate that meets the new law would seem to make perfect sense. Not so fast! Before rushing a purchase order through, take time to determine:

  • Motor efficiency versus nameplate
  • Motor efficiency versus load

To clarify: Yes, you'll improve overall efficiency around two efficiency points by replacing a standard efficient motor with a new EISA premium efficient model. There's much more to be gained, however, by making a few calculations.

Motor nameplate data doesn't identify precise motor efficiency—only a range as defined by NEMA. An induction motor is highly efficient when operating close to its rated torque and speed, but it still has five major components of loss: iron loss, copper loss, frictional loss, windage loss and sound loss. Together, they add up to the total loss of the motor.

Frictional, windage and sound losses are constant, independent of shaft load and typically very small. The major losses are from iron and copper. Iron loss is essentially constant and independent of shaft load, while copper represents a I2R loss, which is shaft-load dependent. Since iron loss is voltage-dependent, it will reduce with reducing voltage.

Most electric motors are designed to run at 50% to 100% of rated load, with maximum efficiency usually near 75%. Thus, a 10 hp motor has an acceptable load range of 5 hp to 10 hp, with peak efficiency at 7.5 hp. Motor efficiency tends to decrease dramatically below about 50% load. The range of good efficiency, however, varies with individual motors and tends to extend over a broader range for larger units. A motor is considered under-loaded when it's in the range where efficiency drops significantly with decreasing load. Throw in a poor motor rewind, and you could have a far-less-efficient motor than the nameplate data indicates.

It is also a well-known fact that motor pumping systems (most pumps are motor-driven) operate at less than 40% efficiency. Clearly, there's an opportunity to save additional energy by reducing the size of the motor.

Keep these points in mind when you set out to calculate true motor efficiency:

  • Use power, amperage or slip measurements to identify the load imposed on the operating motor.
  • Obtain a motor part-load efficiency value consistent with the approximated load from the manufacturer. Or, if direct-read power measurements are available, derive a revised load estimate using both the power measurement at the motor terminals and the part-load efficiency.

If your company tracks energy savings and justifies projects based on documented payback, evaluating your motor performance/load is important. Help is out there. Several commercially available devices will do these calculations for you. If you don't have the resources within your plant to make the calculations, contact a local EASA (Electrical Apparatus Service Association) shop that offers
this service. UM


Bill Livoti is a fluid power and power industry engineer with Baldor Electric Company. Telephone: (864) 281-2118; e-mail: This e-mail address is being protected from spambots. You need JavaScript enabled to view it

Newsletter Sign Up

Your First Name:

Your Last Name:

Your E-Mail Address:

Would you like our Newsletter?:

Enter verification image value

Congratulations to Our Recent Survey Winner

Paul Kimble, a Vibration Analyst for General Motors, was chosen at random to win a $100 gift card for completing our recent online MT Buying Cycle Survey. You could win, too! Watch your e-mail for our next survey request.

Featured Supplier: Brady

bradyBrady Worldwide Inc. is an international manufacturer and marketer of complete solutions that identify and protect premises, products and people. Our products include high-performance labels and signs, safety devices, printing systems and software, and precision die-cut materials. Along with being a global leader in industrial and safety printing systems and solutions, we have been the company you trust when performance matters most since 1914. We serve customers in electronics, telecommunications, manufacturing, electrical, construction, education, medical and a variety of other industries.

Click here for more.

Featured White Paper: Spraying Systems Co.

SSCo Logo Color w tag

Clean Tanks Faster and Lower Operating Costs

Understanding all the tank cleaning equipment options is difficult because not all tank cleaning nozzles are created equal. Let Spraying Systems Co. show you how to reduce cleaning time, minimize liquid consumption and improve cleaning effectiveness. 

Click here to download the White Paper.